curing temperature

The properties of the inorganic cementing and grouting materials for fast anchorage ( abbreviated to ICG-ⅲ) and the effect of curing temperature were studied.

研究了一种无机快速锚固灌注材料（ICG-Ⅲ）的性能及施工温度对其性能的影响。

The customer can use OPP by standard thick film printing process with curing temperature 200 ℃.

采用厚膜印刷工艺，200℃固化。

The hardness of highlights oil and different light oil have different best curing temperature.

度高光油的硬度好,而且不同的光油有不同的最佳固化温度.

Forming curing tank after the curing temperature of168~ 180 ℃.

成型后在硫化罐内硫化，温度为168～180℃。

Minimum temperature for curing is-10 ℃.

最低固化温度为 -10 ℃.

Study on a new class F low temperature fast-curing solvent impregnating varnish

新型F级低温快固化有溶剂浸渍漆的研制

It can be quicky cured and resisted high temperature for class H in a short curing time and low evaporation losses.

它耐高温达到H级，固化速度快，贮存周期长，挥发率低。

However, the high benzoxazine resin curing temperature, low cross-linking density of the cured product, brittle and other defects restrict its application in some special fields.

但是，苯并恶嗪树脂固化温度偏高、固化产物交联密度偏低、性脆等缺陷制约了其在一些特殊领域的应用。

The key consideration and the pouring temperature of the concrete under low temperature construction, curing temperature, heat storage and holding time parameters on the maximum temperature rise inside the concrete, as well as the size of the surface tensile stress, and draw some useful conclusions.

重点考虑和阐述了混凝土在冬季施工下的浇注温度、养护温度、蓄热保温时间等参数对混凝土内部最高温升以及表面拉应力大小的影响，得出了一些有益的结论。

Experiment on the Electric-type temperature and humidity-controlled intensive tobacco oven designed by Henan Agricultural University was conducted to study the trend of the major mineral elements content in curing process and the effects of mineral element contents in cured leaf in different baking conditions.

采用河南农业大学设计的电热式温湿自控密集烤烟箱，研究了烘烤过程一些主要矿质元素含量的变化趋势及不同烘烤条件对烤后烟叶矿质元素含量的影响。

This may be done in a reciprocating screw machine where one charge at a time is brought to curing temperature.

这可能是在做往复螺杆机，其中一名主管在一个时间是带来的固化温度。

Determination of Curing Temperature and EV Time for Thick walled Rubber Article

橡胶厚制品硫化温度与等效硫化时间的测定

The numerical simulation method can be used to optimize the curing temperature cycle, which can improve the quality of composite products.

模拟程序可以计算得到任意时刻复合材料内温度及固化度分布，通过数值模拟可以有效地优化固化加热工艺参数，提高产品质量。

For traditional thermal curing powder coatings, there has a big limit of high curing temperature.

但普通的粉末涂料存在固化温度偏高,不能用于热敏性底材,限制了其应用范围.

Determination on curing temperature curve of paints for coloured sheet

彩板涂料固化温度曲线的测定

When curing temperature was preferred to be 260 and the percentage of solidification agent was 3 %.

固化剂质量分数为3%,固化温度为260℃时得到的膜的性能最佳.

the influence of treating methods of the cotton fabric, curing temperature, addition of salt and bath ratio upon dyeing are also discussed.

文章还讨论了棉织物处理方式、焙烘温度、盐及染色浴比对染色的影响。

Take the average temperature in the curing time as curing temperature.

养护温度取各湿喷桩养护期的平均气温。

Moderate curing pressure and curing temperature were beneficial to composite properties.

适中的固化压力与固化温度有利于材料具有较好的力学性能与导电性能。

a model was built by using ansys to simulate the curing temperature field of two green tires, of which one was preheated and another was not.

采用ANSYS建立轮胎硫化温度场分析模型，对经过预热和未经预热处理两种情况下的胎坯硫化温度场进行了模拟。

In order to determine reasonable processing parameters, heating of thermosetting molding compound in the mold and that of heat transfer after curing temperature are analyzed.

本文就模压料在模具中加热过程和达到固化温度以后的传热过程进行定量分析，以确定合理的工艺控制参数。

Preparation of acid-resistant non-solvent epoxy adhesive with low curing temperature for lead-storage battery

低温固化铅酸蓄电池用防腐耐酸无溶剂环氧胶粘剂的研制

This paper studies the effect of the formulation of the cold curing epoxy copper powder electric conductive adhesive, curing temperature, curing velocity, using temperature pot life and storage life on the properties of the adhesive.

本文研究了冷固化环氧型铜粉导电胶的配比、固化温度、固化速度、使用温度、各种介质、适用期和贮存期对性能的影响。

Of course, curing temperature is not possible.

当然固化温度并不是越高越好.

It's curing temperature high and difficult to molding.

聚酰亚胺固化温度太高,并且难于成型加工.

Come through the curing temperature by differential scanning calorimetry ( DSC), Curing trial in combination with curing reaction appropriate curing time.

通过差式扫描量热法（DSC）得出固化温度，并结合固化试验得出固化反应适宜的固化时间。

A series of trials on cement-stabilized base course mateials, such as unconfined compressive strength, dry shrinkage and temperature shrinkage, were done under the condition of curing temperature 25 ° C and 10 ° C.

在养生温度为25°C和10°C的情况下，分别对水泥稳定碎石基层材料进行无侧限抗压强度试验、干缩试验以及温缩试验。

The experimental results show that the curing temperature of the modified MDPES for making the composite mainly depend on both the reaction of network formation and the cleavage of the ether linkages in BE.

研究表明，选择BE/MDPES的固化温度时，必须同时考虑网络的形成反应和BE中醚键的断裂反应。

Influence of Curing Temperature on Performance of Epoxy Thermosets

固化温度对环氧树脂固化物性能的影响

A study was made on concrete creep under different curing temperatures, and the comprehensive effects of time and temperature on creep development were expressed with the chemical reaction rate.

对不同养护温度下的混凝土徐变进行了研究，用化学反应速率描述温度对混凝土徐变的影响。